Aluminium Alloys Products

• Excellent joining characteristics
• Good acceptance of applied coatings
• Combines relatively high strength
• Good workability
• High resistance to corrosion
• Combines relatively high strength,good workability,and high resistance to corrosion

• Aircraft fittings
• Gears and shafts
• Fuse parts
• Meter shafts and gears
• Missile parts
• Regulating valve parts
• Worm gears
• Keys
• Commercial aircraft
• Aerospace
• Defense equipment

• 7075 in the T6 condition has a machinability rating of 80% when compared to 2011 at 100%. Aluminum 7075 is can be formed in the annealed condition. and can be forged in the temperature range of 700 Degrees to 900 Degrees F. It should be solution heat treated following forging. Aluminum 7075 is a very poor choice for welding. Resistance welding is the only preferred method of joining 7075. Gas welding should be avoided and the use of arc welding may result in degradation of corrosion resistance.

• Moderate corrosion resistance
• The over aged -T73 and -T7351 tempers
• Offers good stress-corrosion cracking resistance as compared to the -T6 and -T651 tempers

• 7075 may be solution annealed at 900 Degrees F for 2 hours at temperature, followed by a water quench. The alloy may then be given a precipitation hardening (aging) heat treatment.

• Good using commercially available methods
• The alloy can be both hard and clear-coat anodized

• Annealing is done at 775 Degrees F, holding for 3 hours at temperature. Controlled cooling at 50F per hour should then be used down to 500F from which it can be air cooled.
• Aluminium Alloy 7075 offers the highest strength of the common screw machine alloys. The superior stress corrosion resistance of the T173 and T7351 tempers makes alloy 7075 a logical replacement for 2024, 2014 and 2017 in many of the most critical applications. The T6 and T651 tempers have fair machinability. Alloy 7075 is heavily utilized by the aircraft and ordnance industries because of its superior strength.

• High functionality
• Perfect finish
• Sturdiness

• High strength aluminum screw machine stock alloy
• Typical tensile strengths in the T351 and T4 temper equal

• Aircraft fittings and structures
• Brake components
• To manufacture of aircraft structures and truck frames

• Alloy 2024 offers good machinability when machined using single-point
• Multi-spindle carbide tools on Screw machines
• The use of a chip breaker is recommended

• Anodizing response is rated moderate for the alloy
• Alloy 2024 can accept all types of anodic coatings

• Precipitation hardening alloy with good strength after heat treatment

• Electrical conductivity 33% of copper

• Shear strength: O (annealed) temper 18 KSI
• T4 temper 38 KSI
• T6 Temper 42 KSI

• Precipitation hardening alloy with good strength after heat treatment

• To manufacture of aircraft structures and truck frames

• Electrical conductivity 33% of copper

• Shear strength: O (annealed) temper 18 KSI
• T4 temper 38 KSI
• T6 Temper 42 KSI

• Wire
• Sheet
• Plate
• Strip
• Round bars
• Hexagonal
• Flats
• Square
• Angle
• Channel
• Blanks
• Tubes
• Billets
• Pipes
• Pipe fittings
• Forging rings
• Special shape forgings
• Fasteners

Product Attribute:

• Dimensions (l x b x h): All
• Anodised: Yes

Specifications:

Chemistry Data:

• High strength aluminum screw machine stock alloy
• Typical tensile strengths in the T351 and T4 temper equal

• Fasteners Etc.
• Aircraft fittings and structures
• Computer parts
• Gears
• Shafts
• Hinge pins
• Valve blocks and valve parts
• Bolts
• Nuts
• Fasteners
• Truck parts
• Brake components

• Alloy 2024 offers good machinability when machined using single-point
• Multi-spindle carbide tools on Screw machines
• The use of a chip breaker is recommended

• Anodizing response is rated moderate for the alloy
• Alloy 2024 can accept all types of anodic coatings

• Precipitation hardening alloy with good strength after heat treatment

• To manufacture of aircraft structures and truck frames

• Electrical conductivity 33% of copper

• Shear strength: O (annealed) temper 18 KSI
• T4 temper 38 KSI
• T6 Temper 42 KSI

• Wire
• Sheet
• Plate
• Strip
• Round bars
• Hexagonal
• Flats
• Square
• Angle
• Channel
• Blanks
• Tubes
• Billets
• Pipes
• Pipe fittings
• Forging rings
• Special shape forgings
• Fasteners

Keeping in mind the precise demands of clients, we offer a wide range of HE30 Aluminium Alloy.

Chemical Composition:

Mechanical Properties:

Physical Properties:

Features:

• Sturdiness
• Finest quality
• High efficiency

• Applications: Commonly used in the manufacture of structural
• Components: Used in high temperature applications as well as high strength amendments
• Mach-inability: In the annealed condition this alloy is readily machined
• Forming: The alloy may be readily formed by conventional methods
• Welding: Welding heat input affects the corrosion resistance of this alloy in an adverse manner
• Heat treatment: Solution heat treatment is done at 1000 F Followed by a cold water quench (T4 condition)
• Forging: Hot forging may be done providing the finished product is given The aging heat treatment to restore corrosion resistance
• Hot working: Hot working should be avoided unless it is feasible to give the finished product The aging heat treatment after all hot working is done
• Cold working: Cold working by conventional means is readily accomplished
• Annealing:Solution annealing is done at 1000 F for adequate time to allow thorough heating, followed by a cold water quench
• Hardening: This alloy is hardened (strengthened) by an aging Heat treatment: By controlled cold working from the solution annealed condition
• Other Physical Props: Electrical conductivity 30% that of copper
• Physical data: Density (lb/cu. in.) 0.103 Specific gravity: 2.84 Melting point (Deg F): 950 Modulus of elasticity tension: 10.6

• Refineries & Petrochemicals
• Oil & Gas
• Chemicals & Fertilisers
• Pneumatic
• Aerospace
• Pharmaceutical
• Robotics
• Electrical and other projects

Product Attribute:

• Size: All
• Thickness: All
• Brand Preference: Hindalco, jindal ,Balco, NALCO , MALCO, Imported (Chinese, USA, Russian, European and Other)
  

Being a client-centric organization, Mallinath Metal Is Importing, supplying and exporting a comprehensive range of HE15 Aluminum Alloy. The aluminum alloy offered by us is highly applauded for their features like low maintenance, dimensional accuracy and high tensile strength. Further, our appointed quality controllers closely inspect our range on different parameters to ensure flawlessness.

Principal design features:

Precipitation hardening alloy with good strength after heat treatment

Applications:

To manufacture of Aircraft structures, Marine, and truck frames, Alloy Wheels, Aerospace, Engineering Works, Pneumatics, Die Making, Automation, Space Aircraft,

Other Mechanical Properties:

• Shear strength: O (annealed) temper 18 KSI
• T4 temper 38 KSI
• T6 Temper 42 KSI

Forms shapes:

• Sheet
• Plate
• Strip
• Round bars
• Hexagonal
• Flats
• Square
• Blanks
• Billet

• High-Grade Raw Material
• High-End Technology
• Rigorously Inspected Fitting
• Precisely-designed
• Easy to install
• Sturdy construction

• Bright and clear coating
• Do not produce brittleness
• Cause substantial lowering of the melting point

• Cooking Utensils
• Food Processing Equipments,
• Storage Tanks and Many More
• Also used in inner and outer panels and components in trucks.

• Bright and clear coating
• Do not produce brittleness
• Cause substantial lowering of the melting point

Backed by rich industry experience, we are engaged in providing our clients with a quality-assured range of 5086 Aluminum Alloy. Precision-engineered, our offered aluminum alloy is manufactured utilizing quality approved raw material and other basic components that are sourced from reliable vendors of the industry. Further, our offered products are manufactured in adherence with the international standards of quality.

Features:

• High tensile strength
• Low maintenance
• Dimensional accuracy
• High ductility

Products details: